Skip to main content Skip to page footer

LED Dimmer LED-01E-PM-DMX-10000

LED Dimmer with one constant voltage output, CV (constant voltage) with maximum 10000mA. Dimming 0-100% high resolution.

Quick Facts

  1. 1 dimming channel max. 24V, 10000mA
  2. dimming 0-100%
  3. protocol ISYGLT or DMX512 16 bit
  4. adjustable dimming frequency

The LED Dimmer was developed for the control of LED lights with fixed voltage connection (integrated current regulation in the LEDs), e.g. LED strips. This makes it possible to control the brightness of the LEDs between 0 and 100% absolutely flicker-free with a dimming resolution of 16 bit (internal resolution at ISYGLT operation). The LED Dimmer can be set to absolute time calculation by parameterising speed calculation. With this all imaginable control tasks can be easily implemented.

The LED Dimmer can optionally be operated on the ISYGLT BUS or DMX512 BUS.

The regular DMX GND connector on PIN 1 is not required and therefore not connected.

The following functions can be performed independently by the LED Dimmer:

  • Calculation of rise times from 0.5 seconds to 12 hours
  • Independent movement from current ACTUAL values to preset SET values at a preset speed (optional in preset time)
  • Feedback "Setpoint reached" after execution of time functions
  • Stop function during the execution of time functions
  • OVERSAMPLING error correction: With the so-called "OVERSAMPLING", the module automatically corrects the jumps in dimming values caused by the cycle times of the BUS system. For this purpose, the dimming values between the BUS cycles are transformed back into the resolution of 16 bit by linearisation. This prevents, for example, flickering when controlling dimmers. During programming, the OVERSAMPLING is referred to as the SOFT function.
  • Execution of flashing functions
  • Adaptation to various LED modules
  • Calculation of defined and definable curves
  • Calculate Min and Max settings to use full 16 bit width
  • Complex emergency operation function

Electrical Data

Operating voltage 12V or 24V for the supply of the LEDs depending on type
Mains fuse max. 16A at Umax 24V DC
Current consumption max. 30mA without load
Output 1 circuit with max. 24V / 10A / max. 240W
NPN switching (- control) Back-up fuse max. 16A, external power supply required
BUS control ISYGLT / DMX512
Cable length power supply
to LED dimmer
max. 20m (observe max. permissible voltage drop for cable cross-section calculation)
Cable length LED dimmer
to last LED
max. 50m (observe max. permissible voltage drop for cable cross-section calculation)
Dimming resolution 16 bit
Subnet (RS-485) max. 5.6V limitation by Z-diodes
Connection screw terminals power supply and LED max. 4mm², BUS 1.5mm²
Operating temperature -10...+45°C
Storage temperature -25...+70°C
Humidity 0...85 % r.h. non-condensing
Protection class IP 10

Design, Dimensions, Weight

Design plastic housing for lamp installation
Dimensions LxWxH 140x35x27mm
Weight 70g

Ordering Data and Conformity

Type designation LED-01E-DMX-PM-10000
Article no. 80028080
Make ISYGLT
Conformity CE

DIP switch ISYGLT BUS operation

SwitchFunctionDescription
DIP 1Protocol 1OFF
DIP 2ReserveOFF
DIP 3ReserveOFF
DIP 4Address bit 7Module address (highest bit)
DIP 5Address bit 6Module address
DIP 6Address bit 5Module address
DIP 7Address bit 4Module address
DIP 8Address bit 3Module address
DIP 9Address bit 2Module address
DIP 10Address bit 1Module address (lowest bit)

DIP switch DMX512 operation

DMX operation with delay (oversampling of 8-bit to 16-bit values)
Default 50ms, adjustable by parameterization from 10ms to 1s, and "Soft"

SwitchFunctionDescription
DIP 1Protocol 1ON
DIP 2Address bit 9Module address (highest bit)
DIP 3Address bit 8Module address
DIP 4Address bit 7Module address
DIP 5Address bit 6Module address
DIP 6Address bit 5Module address
DIP 7Address bit 4Module address
DIP 8Address bit 3Module address
DIP 9Address bit 2Module address
DIP 10Address bit 1Module address (lowest bit)

 

Example for DMX address setting

DIP switchoutput
Address 1000000001DMX channel 1
Address 10000001010DMX 10
Address 127001111111DMX 127
Address 510111111110DMX 510

Function Indicators (LEDs on the Module)

LEDDesignationStateMeaning
red POWEROffNo operating voltage
OnOperating voltage, no error
blinkingSignalisation parameter error
yellowBUSOffBUS wiring error
OnBUS communication error (address not recognised)
blinkingInterference-free data transmission via the BUS line
green RegelnONIndicates that the dimming channel is active

Software


Parameterisation with ProgramDesigner

In the ISYGLT ProgramDesigner there are various parameterisation possibilities:

  • setting of various dimming curves
  • setting of fade times
  • calculation of fade times
  • minimum and maximum values
  • adjustment of PWM frequency
  • emergency operating functions
  • flash mode

Pin Assignment

Terminals LED side

+Ub Voltage input + for LED supply
GND Voltage input - for LED supply
LED (+) Anode (+) of the LED
LED (-) Cathode (-) of the LED

Terminals BUS side

A Subnet (BUS A, RS-485)
A Subnet (BUS A, RS-485)
B Subnet (BUS B, RS-485)
B Subnet (BUS B, RS-485)

Variants

LED-04ECM-DMX-200
Article no. 80028346, 4-channel LED dimmer for power LED (200mA) with colourfast dimming and colour temperature control
LED-04ECM-DMX-350
Article no. 80028042, 4-channel LED dimmer for power LED (350mA) with colourfast dimming and colour temperature control
LED-04ECM-DMX-500
Article no. 80028049, 4-channel LED dimmer for power LED (500mA) with colourfast dimming and colour temperature control
LED-04ECM-DMX-700
Article no. 80028047, 4-channel LED dimmer for power LED (700mA) with colourfast dimming and colour temperature control
LED-03EC-DMX-350-V2
Art. no. 80028051, 3-channel LED dimmer for power LED (350mA) with colourfast dimming, with housing,
for very noise-sensitive applications
LED-02E-DMX16-700-V2
Article no. 80028380, 2-channel LED dimmer for power LED (700mA), with housing, for very noise-sensitive applications,
2nd protocol DMX512-16Bit
LED-03EC-DMX-700-V2
Art. no. 80028070, 3-channel LED dimmer for power LED (700mA) with colourfast dimming, with housing,
for very noise-sensitive applications
LED-02E-DMX-1000
Article no. 80100316, 2-channel LED dimmer for power LED (1000mA), with housing
LED-04B-ANA-DMX
Article no. 80028304, 4-channel non-PWM analog LED dimmer for power LED (250mA-1550mA), in DIN rail mounted housing

To top