Depending on configuration and LED type, this Dimmer can control LEDs with a total of 300W (4x 75W) power. Recommended areas of use are all areas in which healthy lighting is ensured, as the effects of conventional PWM dimming have not been fully investigated, but are classified by experts as posing a health risk. PWM is used as standard in all previous LED Dimmers, including the DALI and KNX/EIB standards. Therefore, the use of non-PWM dimming is particularly recommended in areas where people stay longer or where high demands are placed on lighting quality:
The LED Dimmer can be operated either on the ISYGLT-BUS or DMX512-BUS.
The following functions can be performed independently by the LED Dimmer:
| Operating voltage | 24V to 56V for the supply of the LEDs depending on the type |
| Emergency operation input | 24V to 56V DC |
| LED forward voltage | 12V to 54V (depending on the voltage drop of the line); the LED forward voltage including the voltage drop of the line must be 2V lower than the supply voltage! |
| Mains fuse | max. 16A at Umax 56V DC |
| Current consumption | max. 1550mA per LED circuit |
| Output | 4 x constant current, separately adjustable in the factory with 250mA to 1550mA each for power LEDs (please specify the desired current value for each circuit when ordering) |
| Power loss | idle circuit: 0.162W / channel, full load and worst conditions: 2.5W / channel |
| BUS control | ISYGLT / DMX512 8/16-bit (others on request) |
| Cable length power supply to LED dimmer | max. 20m (observe max. permissible voltage drop for cable cross-section calculation) |
| Cable length LED dimmer up to last LED | max. 50m |
| Dimming resolution | 16 Bit |
| Subnet (RS-485) | max. 5.6V limitation by Z-diodes |
| Connection | screw terminals 2.5mm² |
| Operating temperature | -10°C to +45°C |
| Storage temperature | -25°C to +70°C |
| Humidity | 0...85 % r.h. non-condensing |
| Protection | IP 20 |
| Switch | Function | Description |
|---|---|---|
| DIP 1 | Protocol 1 | OFF |
| DIP 2 | Protocol 2 | OFF |
| DIP 3 | Reserve | OFF |
| DIP 4 | Reserve | OFF |
| DIP 5 | Reserve | OFF |
| DIP 6 | Address bit 7 | Module address (highest bit) |
| DIP 7 | Address bit 6 | Module address |
| DIP 8 | Address bit 5 | Module address |
| DIP 9 | Address bit 4 | Module address |
| DIP 10 | Address bit 3 | Module address |
| DIP 11 | Address bit 2 | Module address |
| DIP 12 | Address bit 1 | Module address (lowest bit) |
DMX operation with delay (oversampling of 8-bit to 16-bit values)
Default 50ms, adjustable by parameterization from 10ms to 1s, as well as "Soft".
DMX 8-bit = DIP 1 = ON, DIP 2 = OFF
DMX 16-bit = DIP 1 = ON, DIP 2 = ON
| Switch | Function | Description |
|---|---|---|
| DIP 1 | Protocol 1 | ON |
| DIP 2 | Protocol 2 | OFF |
| DIP 3 | Channel setup | OFF = 4 different (sequential) DMX addresses, ON = all outputs at 1 DMX address |
| DIP 4 | Address bit 9 | DMX start address (highest bit) |
| DIP 5 | Address bit 8 | DMX start address |
| DIP 6 | Address bit 7 | DMX start address |
| DIP 7 | Address bit 6 | DMX start address |
| DIP 8 | Address bit 5 | DMX start address |
| DIP 9 | Address bit 4 | DMX start address |
| DIP 10 | Address bit 3 | DMX start address |
| DIP 11 | Address bit 2 | DMX start address |
| DIP 12 | Address bit 1 | DMX start address (lowest bit) |
Example: DMX address setting
| DIP switch | Output | |
|---|---|---|
| Address 0 | xxx000000000 | Switch on manually to the value "Emergency operation" (default 100%) |
| Address 1 | xxx000000001 | DMX channels 1, 2, 3 and 4 |
| Address 10 | xxx000001010 | DMX channels 10, 11, 12 and 13 |
| Address 127 | xxx001111111 | DMX channels 127, 128, 129 and 130 |
| Address 509 | xxx111111101 | DMX channels 509, 510, 511 and 512 |
| LED | Designation | State | Meaning |
|---|---|---|---|
| red | POWER | Off | No operating voltage |
| On | Operating voltage, no error | ||
| blinking | Signalisation parameter error | ||
| yellow | BUS | Off | BUS wiring error |
| On | BUS communication error (address not recognised) | ||
| blinking | Interference-free data transmission via the BUS line | ||
| 4x green | LED 1-4 | dimming | Signals the intensity of the respective output |
In the ISYGLT ProgramDesigner there are various parameterisation possibilities:
Operating modes:
Setting of various dimming curves
Minimum and maximum values
| A | Subnet (BUS A, RS-485) ISYGLT or DMX |
| B | Subnet (BUS B, RS-485) ISYGLT or DMX |
| GND | GND RS-485 |
| T+ | Temperature sensor + |
| T- | Temperature sensor - |
| U- | Operating voltage input - for LED dimmer |
| U+ | Operating voltage input + for LED dimmer |
| LED-04ECM-DMX-200 Article no. 80028346, 4-channel LED dimmer for power LED (200mA) with colourfast dimming and colour temperature control |
| LED-04ECM-DMX-350 Article no. 80028042, 4-channel LED dimmer for power LED (350mA) with colourfast dimming and colour temperature control |
| LED-04ECM-DMX-500 Article no. 80028049, 4-channel LED dimmer for power LED (500mA) with colourfast dimming and colour temperature control |
| LED-04ECM-DMX-700 Article no. 80028047, 4-channel LED dimmer for power LED (700mA) with colourfast dimming and colour temperature control |
| LED-03EC-DMX-350-V2 Art. no. 80028051, 3-channel LED dimmer for power LED (350mA) with colourfast dimming, with housing, for very noise-sensitive applications |
| LED-02E-DMX16-700-V2 Article no. 80028380, 2-channel LED dimmer for power LED (700mA), with housing, for very noise-sensitive applications, 2nd protocol DMX512-16Bit |
| LED-03EC-DMX-700-V2 Art. no. 80028070, 3-channel LED dimmer for power LED (700mA) with colourfast dimming, with housing, for very noise-sensitive applications |
| LED-02E-DMX-1000 Article no. 80100316, 2-channel LED dimmer for power LED (1000mA), with housing |
| LED-04B-ANA-DMX Article no. 80028304, 4-channel non-PWM analog LED dimmer for power LED (250mA-1550mA), in DIN rail mounted housing |
Article no.: 80028304
