Leading Edge Dimmer TD-500-M2/BP

Thyristor Dimmer in Leading Edge technology (incandescent bulb), high-voltage halogen lamps, low-voltage halogen lamps with magnetic transformer 2 channels with up to 500W/VA each.

Quick Facts

  • 2 channels each 500W Leading Edge
  • protocol ISYGLT
  • protocol DMX512
  • protocol 1-10V / 0-10V
  • single-button dimmer

The thyristor dimmer is a classic Leading Edge Dimmer in 16Bit "Thyristor Antiparallel Technology". This type of control is certainly the upper class of dimmers and cannot be compared to the simpler triac dimmers. The control and monitoring for each half-wave is carried out separately here, since a thyristor is available and responsible accordingly. The dimmer is characterised by its extreme robustness in the respective power class. In leading edge technology, all ohmic loads (incandescent lamps, high-voltage halogen lamps, heaters) and inductive loads (halogen with magnetic transformers, fluorescent lamps with VIP-90, motors, plastic welding equipment with magnetic transformers) can be operated. The dimmer has several control modes and can be operated conventionally with potentiometer, button, 0-10V or 1-10V signal or digitally in ISYGLT-BUS, DMX512 8-Bit or DMX512 16-Bit. The basic function parameters are set via 2 DIP switches; detailed parameters can only be set in the ISYGLT system.

Electrical Data

Mains supply 230V / 45 to 65 Hz
Mains fuse 1 x 230V automaton B6A or B10A
Output 2 x 230V leading edge 35W to 500W per channel
Power loss <2 ... 13W (Stand-by ... full load)
!! Please ensure sufficient ventilation of the switch cabinet or housing!
1 (0)-10V sink current at 1-10V = 1mA
source current with hardware option 0-10V = 0.5mA at 20kOhm
Insulation voltage 3500V (ISYGLT-BUS / mains)
Overtemperature protection temperature fuse (bimetal) 105°C +/-5K self-resetting in the primary circuit of the dimmer
(contact rating 10A at Cos-Phi=1; 6.3A at Cos-Phi=0.6)
Subnet (RS-485) max. 5.6V limitation by Z diodes
Connection screw terminals 1.5mm² pluggable
Operating temperature -10...+45°C
> at +50°C max. 60% connectable power
> at +55°C max. 50% connectable power
> at +60°C max. 30% connectable power
Storage temperature -25...+70 °C
Humidity 0...85 % r.h. non-condensing
Protection class IP 30
Protection class I

Design, Dimensions, Weight

Design DIN rail housing
Dimensions WxHxD 106x90x59mm rail-mounted device (6 HP)
Weight 410 g

Ordering Data and Conformity

Type designation TD-500-M2/BP
Article no. 80026610
Make ISYGLT
Conformity CE

DIP switch ISYGLT-BUS operation

OFFDIP topON
OFFOFF1 
Address 0 to 127 2Address bit 6
 3Address bit 5
 4Address bit 4
 5Address bit 3
 6Address bit 2
 7Address bit 1
 8Address bit 0
 OFFDIP belowON
All OFF OFF1 
OFF2 
OFF3 
OFF4 
OFF5 
OFF6 
OFF7 
OFF8 

DIP switch stand-alone operation

OFFDIP topON
All OFFOFF1
OFF 2
OFF3
OFF4 
OFF 5
OFF6
OFF 7
OFF 8
OFFDIP belowON
ModeOFF1
Mode 2Stand-alone
OFF3Speedalaising (Oversampling) ON
U-inputs 0-10V4U-inputs 1-10V
Linear dimming curve5Visor dimming curve
Function off6Min dimming level
Curve linear7Min dimming level
 Mode Analog inputs8Mode 1-Button dimmer

DIP switch standard (stand-alone) operation 1-channel dimmer (1x1000W expandable with slave)

OFF
DIP top
ON
DMX address bits 1Address bit 7
 2Address bit 6
 3Address bit 5
 4Address bit 4
5Address bit 6
 6Address bit 2
 7Address bit 1
 8Address bit 0
OFF
DIP below
ON
Mode 1ON = DMX512
Mode 2ON + 1 ON = DMX512-16Bit
OFF OFF3Speedalaising (Oversampling) ON
U-inputs 0-10V4U-inputs 1-10V
Linear dimming curve5Visor dimming curve
Function off6Min dimming level
Curve linear7Min dimming level
DMX address bits8Address bit 8

Function Indicators (LEDs on the Module)

LEDDesignationStateMeaning
redPowerOFFNo operating voltage
ONOperating voltage, no error
yellowBUSOFFNo BUS signal detected
ONBUS signal detected, own address not detected
Even blinkingBUS signal and own module address detected
greenState of dimmer outputsOFFOutput "OFF" no error
ONOutput "ON" no error

Software


Parameterisation with ProgramDesigner

  • setting the dimming curves
  • feedback of the dimmer status (diagnostic messages)
  • emergency operation in case of BUS failure

Pin Assignment

9-pole connector left

GND Reference potential (ground) for the voltage inputs (0-10V) and BUS RS485 (internally connected with the seventh terminal)
UE1 Control voltage input for the dimmer output LD1 (emergency function)
UE2 Control voltage input for the dimmer output LD2 (emergency function)
+10V 10V for the connection of an external potentiometer
S1 Voltage channel 1 for sink current 1-10V (insert bridge to "UE1")
S2 Voltage channel 2 for sink current 1-10V (insert bridge to "UE2")
GND Reference potential (ground) for the voltage inputs (0-10V) and BUS RS485 (internally connected with the first terminal)
A Subnet (BUS A, RS-485)
B Subnet (BUS B, RS-485)

6-pole connector right

LD1 Dimmer 1 load output 0...230V max. 500W/VA leading edge
LD2 Dimmer 2 load output 0...230V max. 500W/VA leading edge
L Mains voltage 230V (45Hz-65Hz)
N Neutral conductor
N Neutral conductor
PE Protective conductor

Additional Equipment

  • DGL-01U - Dynamic Base Load for LED lamps
  • DIN rail adapter (included)

Variants

Higher power Leading Edge Dimmer

TD-4000-BP

TD-5600-BP

Universal Dimmer UD-700-X2 - especially for LED light sources

Leading Edge, Trailing Edge and Universal Dimmers can also be found in the catalog.

To top

TD-500-sw_bild72.jpg

TD-500-M2/BP

Article no.: 80026610

Thyristor Dimmer with leading edge technology, HV halogen lamps, LV halogen lamps with magnetic transformer. 2 channels with up to 500W/VA each.
+ shipping costs
  • kostenlose Anfrage / free request
    from 1 € 0.00 € 0.00