Lamp Installation Device I/O-02L-230V-10A

I/O Module with 2 binary inputs and 2 relay outputs for 2 lighting circuits. Light terminal device especially designed for installation in lamps.

Quick Facts

  • 2 binary inputs 12-48V
  • 2 relay outputs 230V/10A
  • Special function: emergency operation
  • Lamp installation

The Lamp Installation Device is a module that has been specially designed for direct installation in lamps in terms of housing and technical data. With the relay outputs 2 lighting circuits can be switched. In addition, an emergency operation function is integrated (see DIP switch function). The inputs can be queried via the subnet. The output relays are designed as changeover contacts, i.e. the circuit is closed or opened in the event of a voltage failure.

Electrical Data

Operating voltage 12V to 35V DC or 12V to 27V AC
Current consumption max. 150mA at 35V and full load of the outputs
max. 250mA at 12V and full load of the outputs
Inputs 2x 12-48V AC/DC, input current per input 5mA at 24V
Outputs 2x relay contact 250V AC (DC max. 25V!)
load capacity:
pure ohm's 10A
incandescent lamps 10A
fluorescent lamps uncompensated 6A
fluorescent lamps compensated 4A
low voltage halogen via transformer 10A
phase motor 0.55kW
ECGs manufacturer-dependent, inrush current 100A < 20ms
!! The inrush current of electronic ballasts is up to 100 times the nominal current !!
minimum contact load: 500mW, min. 10V, min. 5mA
Subnet (RS-485) max. 5.6V limitation by Z-diodes
Connection screw terminals 2.5mm², spring type terminals 2x 0.25 - 0.75mm²
Operating temperature -10°C to +50°C
Storage temperature -25°C to +70°C
Humidity 0...85 % r.h. non-condensing
Protection in not installed state IP20

Design, Dimensions, Weight

Design plastic housing for installation in lamps
Dimensions WxHxD 190 x 39.7 x 28.2mm
Weight 100g

Ordering Data and Conformity

Type designation I/O-02L-230V-10A
Article no. 80020250
Make ISYGLT
Conformity CE

DIP switches

10-pole DIP switch for setting the ISYGLT BUS address (0-127) and emergency function is located on the side of the module. DIP switch 1 is intended for the emergency function, DIP switches 2 to 8 are used for the ISYGLT address. DIP switches 9 and 10 are not addressed at this module and remain OFF.

Special function DIP switch 1

DIP-1 SettingMeaning
OFF







Standard

BUS worksThe inputs are read in by the BUS and have no effect on the outputs.
BUS does not workThe inputs remain as they were until the BUS works again.
ONEmergency operationBUS works

If input E1 is set, output A1 is switched on, but the input is still forwarded to the BUS.

If input E2 is set, output A2 is switched on, but the input is still forwarded to the BUS.

If input E1 is reset, output A1 is switched by the BUS, but the input is still forwarded to the BUS.

If input E2 is reset, output A2 is switched by the BUS, but the input is still forwarded to the BUS.

BUS does not work

If input E1 is set, output A1 is switched on.

If input E2 is set, output A2 is switched on.

If input E1 is reset, output A1 is reset.

If input E2 is reset, output A2 is reset.


Function Indicators (LEDs on the Module)

LEDDesignationStateMeaning
redPOWEROffNo operating voltage
OnOperating voltage, no error
yellowBUSOff / OnError BUS
blinkingInterference-free data transmission via the BUS line

Pin Assignment

Spring type terminals

Ub Operating voltage
0V Operating voltage
A Subnet (BUS A, RS-485)
B Subnet (BUS B, RS-485)
E1 Input 1
E2 Input 2

Screw terminals

A2 S Relay output channel 2 NO contact
A2 O Relay output channel 2 NC contact
C Common
A1 O Relay output channel 1 NC contact
A1 S Relay output channel 1 NO contact